From empty
To version 24.1
edited by Peter Karlsson
on 2019/02/06 08:45
Change comment: There is no comment for this version

Summary

Details

Page properties
Title
... ... @@ -1,0 +1,1 @@
1 +Production Settings Unitechnik
Parent
... ... @@ -1,0 +1,1 @@
1 +xwiki:IMPACT Applications.IMPACT for AutoCAD.Form Slabs.WebHome
Author
... ... @@ -1,1 +1,1 @@
1 -XWiki.XWikiGuest
1 +XWiki.PeterKarlsson
Content
... ... @@ -1,0 +1,122 @@
1 +(% class="row" %)
2 +(((
3 +(% class="col-xs-12 col-sm-8" %)
4 +(((
5 +
6 +
7 += Why add extra reinforcement to welded mesh? =
8 +
9 +For a factory with a mesh welding machine it's very important that as much of the reinforcement that design think is needed for the element is added to the welded mesh. This will, of course, result in an easier process in the production when the element shall be put together. This article is a bout how to add reinfocement to the mesh for a FormSlab element.
10 +
11 +
12 += Production settings =
13 +
14 +In Standard Admin there is a production setting that will be used when the command check produciability is used.
15 +
16 +[[image:1524581807717-781.png||height="152" width="651"]]
17 +
18 +//Figure 1: Check produciability FormSlab//
19 +
20 +If changes are made to the Reinforcement the Producability check will be used to check limitations. All not producible bars will be shown in red.
21 +
22 +The setting **Bar Dimension** will reduce which possible bar diameters that are available and all other bar diameters will be red if checked.
23 +
24 +[[image:AT-Production Settings.png]]
25 +
26 +(% style="margin:0cm 0cm 10pt" %)
27 +(% style="font-family:Calibri,sans-serif; font-size:11pt; line-height:115%" %)[[image:1524581676414-607.png||height="396" width="440"]]
28 +
29 +(% style="margin:0cm 0cm 10pt" %)
30 +//Figure 2: Bar Dimensions in Production settings//
31 +
32 +(% style="margin:0cm 0cm 10pt" %)
33 +[[image:1524581887266-425.png||height="147" width="420"]]
34 +
35 +(% style="margin:0cm 0cm 10pt" %)
36 +//Figure 3: Directions and definitions//
37 +
38 +(% style="margin:0cm 0cm 10pt" %)
39 +Longitudinal bars always lie parallel to the lattice girders in the tensioning direction.
40 +
41 +(% style="margin:0cm 0cm 10pt" %)
42 +[[image:1524582020794-174.png||height="155" width="535"]]
43 +
44 +(% style="margin:0cm 0cm 10pt" %)
45 +//Figure 4: Production settings intersection points//
46 +
47 +If the setting **only orthogonal bars** are set to yes only right angled bars are allowed.
48 +
49 +**Welded Mesh** means that the mesh is welded in the production. **Minimum intersection points** means that the bar needs to be crossed by another bar that many times.
50 +
51 +(% style="margin:0cm 0cm 10pt" %)
52 +(% style="font-family:Calibri,sans-serif; font-size:11pt; line-height:115%" %)[[image:1524582165902-891.png||height="211" width="448"]]
53 +
54 +(% style="margin:0cm 0cm 10pt" %)
55 +//Figure 5: Grid longitudinal//
56 +
57 +(% class="MsoCaption" style="text-align:justify; margin:0cm 0cm 10pt" %)
58 +The Grid longitudinal value is the interval of longitudinal bars. The bar is shifted to the nearest grid position. If the grid position is already occupied, the bars are fused together.
59 +
60 +(% class="MsoCaption" style="text-align:justify; margin:0cm 0cm 10pt" %)
61 +[[image:1524582331050-495.png||height="222" width="501"]]
62 +
63 +(% class="MsoCaption" style="text-align:justify; margin:0cm 0cm 10pt" %)
64 +//Figure 6: Spacing longitudinal//
65 +
66 +(% style="margin:0cm 0cm 10pt" %)
67 +These values if the settings are activated (not in this example) are telling the max and min values for the placement of the longitudinal bars.
68 +
69 +(% style="margin:0cm 0cm 10pt" %)
70 +(% style="font-family:Calibri,sans-serif; font-size:11pt; line-height:115%" %)[[image:1524582403412-967.png||height="273" width="451"]]
71 +
72 +(% style="margin:0cm 0cm 10pt" %)
73 +//Figure 7: Grid transverse//
74 +
75 +(% style="margin:0cm 0cm 10pt" %)
76 +The same setting as the Grid longitudinal value but in the transverse direction.
77 +\\These modifiers can modify the bars to meet minimum production requirements after they have been cut.
78 +
79 +(% style="margin:0cm 0cm 10pt" %)
80 +[[image:1549437914658-222.png||height="260" width="699"]]
81 +
82 +(% style="margin:0cm 0cm 10pt" %)
83 +//Figure 8: Production modifiers//
84 +
85 +**A:** this is for the transverse direction means that the bar is allowed to extend longer than it’s allowed because of a CIM or a hole to meet the criteria needed to produce the mesh in the machine.
86 +[[image:1549439025247-696.png||height="237" width="245"]]
87 +
88 +This will later on be cut manually in production. This means bars that is longer than “Remove bars shorter than” and Min transversal bar.
89 +[[image:1549439063389-109.png||height="128" width="453"]]
90 +
91 +**B:** the distance
92 +**C:** The same as A above but in the longitudinal direction
93 +**D:** The same as B above but in the longitudinal direction
94 +**E:** If two bars are overlapping each other in the transversal direction they will be combined to one bar
95 +**F:** Same as E above but for longitudinal bars
96 +
97 +
98 +== How to do it ==
99 +
100 +The movie below describes with an example how to get the extra bars into the welded mesh for FormSlabs.
101 +
102 +{{video attachment="Produciability control FormSlab adding bars to the mesh.mp4"/}}
103 +
104 +
105 +)))
106 +
107 +(% class="col-xs-12 col-sm-4" %)
108 +(((
109 +(% class="box" %)
110 +(((
111 +[[image:1524582256983-924.png||height="118" width="280"]]
112 +//Figure 8: FormSlab welded mesh//
113 +)))
114 +
115 +(% class="box" %)
116 +(((
117 +**Contents**
118 +
119 +{{toc/}}
120 +)))
121 +)))
122 +)))
1524581631794-195.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.PeterKarlsson
Size
... ... @@ -1,0 +1,1 @@
1 +0 bytes
Content
1524581676414-607.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.PeterKarlsson
Size
... ... @@ -1,0 +1,1 @@
1 +0 bytes
Content
1524581807717-781.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.PeterKarlsson
Size
... ... @@ -1,0 +1,1 @@
1 +0 bytes
Content
1524581887266-425.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.PeterKarlsson
Size
... ... @@ -1,0 +1,1 @@
1 +0 bytes
Content
1524582020794-174.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.PeterKarlsson
Size
... ... @@ -1,0 +1,1 @@
1 +0 bytes
Content
1524582165902-891.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.PeterKarlsson
Size
... ... @@ -1,0 +1,1 @@
1 +0 bytes
Content
1524582235858-558.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.PeterKarlsson
Size
... ... @@ -1,0 +1,1 @@
1 +0 bytes
Content
1524582256983-924.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.PeterKarlsson
Size
... ... @@ -1,0 +1,1 @@
1 +0 bytes
Content
1524582331050-495.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.PeterKarlsson
Size
... ... @@ -1,0 +1,1 @@
1 +0 bytes
Content
1524582403412-967.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.PeterKarlsson
Size
... ... @@ -1,0 +1,1 @@
1 +0 bytes
Content
1549437914658-222.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.PeterKarlsson
Size
... ... @@ -1,0 +1,1 @@
1 +0 bytes
Content
1549439025247-696.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.PeterKarlsson
Size
... ... @@ -1,0 +1,1 @@
1 +0 bytes
Content
1549439063389-109.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.PeterKarlsson
Size
... ... @@ -1,0 +1,1 @@
1 +0 bytes
Content
AT-Production Settings.png
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.PeterKarlsson
Size
... ... @@ -1,0 +1,1 @@
1 +0 bytes
Content
Produciability control FormSlab adding bars to the mesh.mp4
Author
... ... @@ -1,0 +1,1 @@
1 +XWiki.PeterKarlsson
Size
... ... @@ -1,0 +1,1 @@
1 +0 bytes
Content
Copyright 2018 StruSoft AB
Impact Documentation