Form Slab Summary
Introduction
This is a customer-specific report that only contains head data.
The report is printed on one page.
Report Setup
General report setup. All the fields have to be filled if you want a summary row at the end of each page.
Page max X and Page max Y defined the maximum size of the report page.
The X-axis is the columns A, B, C etc. The Y-axis is the rows 1, 2, 3 etc.
Continuous Header Row defines in which row the header and footer start, and in this case, it starts from row 10.
Continuous Start Row (in this case from row 11) is where the main information starts and Continuous End Row (in this case until row 40) is where the main information ends.
Header setup:
This report does not have any header set up.
As you can see we have different X and Y values for each field. This is done so the program knows where to put in the specific information into the report.
As mention above, the continuous header starts at row 10 to row 11 in the Y direction.
Here are the fields that can be added to the Header and Footer:
Fields | Description |
BOUNDING_BOX_AREA_55 | |
BOUNDING_BOX_AREA_60 | |
BOUNDING_BOX_AREA_65 | |
BOUNDING_BOX_AREA_70 | |
BOUNDING_BOX_AREA_75 | |
BOUNDING_BOX_AREA_80 | |
BOUNDING_BOX_AREA_85 | |
BOUNDING_BOX_AREA_90_OR_MORE | |
BOUNDING_BOX_AREA_C_REST | |
BOUNDING_BOX_AREA_C3037 | |
BOUNDING_BOX_AREA_C3240 | |
BOUNDING_BOX_AREA_C3240L | |
BOUNDING_BOX_AREA_C3545 | |
BOUNDING_BOX_AREA_C3545L | |
BOUNDING_BOX_AREA_C4050 | |
BOUNDING_BOX_AREA_C4050L | |
BOUNDING_BOX_AREA_C5060 | |
BOUNDING_BOX_AREA_NON_FULL_WIDTH | |
BOUNDING_BOX_AREA_TOTAL | |
BUILDING | |
BUILDING_OWNER_NAME | |
BUILDING_SITE_NAME | |
FLOOR | |
HOLE_DIAMETER_200_OR_LESS | |
HOLE_DIAMETER_201_249 | |
HOLE_DIAMETER_250_799 | |
HOLE_DIAMETER_800_OR_MORE | |
MASS_LATTICE_GIRDERS | |
MASS_REINFORCEMENT_TOTAL | |
MASS_STIRRUPS | |
MASS_STRAIGHT_BAR | |
MASS_WIRES | |
NET_AREA_TOTAL | |
NUMBER_OF_ELEMENTS | |
NUMBER_OF_ELEMENTS_NON_FULL_WIDTH | |
NUMBER_OF_STIRRUPS | |
OTHER_HOLE_AREA_015_OR_LESS | |
OTHER_HOLE_AREA_016_059 | |
OTHER_HOLE_AREA_060_100 | |
OTHER_HOLE_AREA_100_OR_MORE | |
PHASE | |
PROJECT | |
REPORT_FLOORS | |
REPORT_REVISION | |
SELECTION | |
USER_DIVISION_CITY | |
USER_DIVISION_COUNTRY | |
USER_DIVISION_DESCRIPTION | |
USER_DIVISION_FAX | |
USER_DIVISION_NAME | |
USER_DIVISION_PHONE | |
USER_DIVISION_STREET | |
USER_DIVISION_ZIPCODE | |
USER_ID | |
USER_MOBILE | |
USER_NAME | |
USER_PHONE | |
USER_SIGNATURE | |
USER_TITLE |
Selection setup:
The standard setup for the selections.
Continuous setup:
The Continuous setup is where you set up all the information, in this case, about the formslab.
As you can see, here you define only one row because this row will be the bases for this report, from row 11 to 40 like shown further up.
The fields you can add to this section are listed below.
Fields | Description |
AMOUNT | |
ARTICLE | |
DESCRIPTION | |
NAME | |
UNIT |
Print report
From Report Tool
It is possible to make the normal selection on what to print, based on the information you want to get out of the report.
You also have the option to save your selection.