Introduction

The report is not the standard report as many of the other reports we have. Planning data is a difference report. This means that the first time it is run, it returns all the data, the following times it just returns the differences. The report is automatically saved, in the folder given in the report setup.

Design report that can be printed from Report Tool.

Report Setup

General report setup. All the fields have to be filled as it prints a sum row at the end of each page.

1585642874421-856.png

Page max X and Page max Y defined the maximum size of the report page.
The x-axis is the columns A, B, C, and etc. and the Y-axis is the rows 1, 2, 3, and etc.

Continuous Header is defined in which row the header and footer start, and in this case, it starts from row 0.

Continuous start row(in this case it is row 12) is where the main info starts and ends in the Continuous end row.
There is no summary in this report.

As you can see, almost all values are 0 and that is because this is not a traditional report to print but more of extraction of data from the database.

Header setup: 
Here is how the header is set up for this report.

1585647164675-805.png

As you can see we have those x and y values for each field, so the program knows where to put the specific information into the report.

As mention above the Continuous header starts at row 0 to row 9 in the Y direction.

Here are the fields that can be added to the Header and footer:

FieldsDescription
BUILDING 
DIVISION 
FACTORY 
PHASE 
PROJECT 
PROJECT_SUMMARY 
PROJECT_TRIMED 
REPORT_NAME 
REPORT_PAGE_NUMBER 
REPORT_PRINT_DATE 
REPORT_REVISION 
REPORT_REVISION_DATE 
REPORT_TITLE 
SELECTION_PRODUCT 
USER_DIVISION_CITY 
USER_DIVISION_COUNTRY 
USER_DIVISION_DESCRIPTION 
USER_DIVISION_FAX 
USER_DIVISION_NAME 
USER_DIVISION_PHONE 
USER_DIVISION_STREET 
USER_DIVISION_ZIPCODE 
USER_MOBILE 
USER_NAME 
USER_PHONE 
USER_SIGNATURE 
USER_TITLE 

Selection setup:
the standard setup for the selections.

Continuous setup:

Here in Continuous setup is where you set up all the information about holes in this case.

1585647318032-382.png

As you can see, here you define only one row because this row will be the bases for this report, from row 12 like shown further up. 

The fields you can add to this section are listed below.

FieldsDescription
ANGLE_LEFT_SIDE 
ANGLE_RIGHT_SIDE 
BOUNDING_BOX_AREA 
CAST_TYPE 
DELIVERY_DATE 
DESIGNATION 
DIFFERENCE 
DRAWING_DATE_MAX 
DRAWING_NAME 
DRAWING_REVISION 
ELEMENT_BUILDING 
ELEMENT_FLOOR 
ELEMENT_GROUP 
ELEMENT_ID 
ELEMENT_MARK 
ELEMENT_PHASE 
ELEMENT_PROJECT 
ELEMENT_TYPE 
ERECTION_SEQUENCE 
GROSS_AREA 
HEIGHT 
LENGTH 
LENGTH_ROUNDEDUP 
LOAD_NO 
MASS 
MASS_INNER_PANEL 
MASS_OUTER_PANEL 
NBR_CIM_GROUP 
NET_AREA 
PLANNED_DELIVERY_DATE 
PLANNED_DRAWING_DATE 
PLANNED_ERECTION_DATE 
PLANNED_PRODUCTION_DATE 
PLANNED_STORAGE_DATE 
PRODUCTING_DIVISION 
PRODUCTING_FACTORY 
PRODUCT 
PRODUCTION_DATE 
READY_FOR_PRODUCTION 
READY_FOR_PRODUCTION_DATE 
REMARK 
STACK_LAYER_NO 
STACK_NO 
STACK_SEQUENCE_NO 
STATUS 
STRANDPTN 
STYLE 
TOP_LENGTH 
TOP_LENGTH_ROUNDEDUP 
TOP_WIDTH 
VOLUME 
VOLUME_INNER_PANEL 
VOLUME_INSULATION 
VOLUME_OUTER_PANEL 
WALL_ROTATION 
WEIGHT 
WIDTH 
WIDTH_HEIGHT 

Print report

From Report Tool
When printing this report you need to save a selection first based on the data you want to get in the report.

In this case, all parameters are set to <All>

1585652236520-988.png

After you press the print button you will be prompt with the option to create the path for the report. Just press yes to that.

The report will be created and stored under the project.

1585652570370-154.png

If you add elements or change anything in the project and print the report again, the report will make a new file and store the difference in the new file, so that you can see what has been changed in the project.

Example

Here is an example of my first report

1585653768448-469.png

After adding a few more elements and removing some others the new report with the difference looks like this.

1585654389744-716.png

Download

You can download the report template here

Tags:
Created by Oskar Kristinsson on 2020/03/30 13:07
Copyright 2018 StruSoft AB
IMPACT Documentation